FOR SALE $6500.00, Makes 78HP 102LB TQ. Dyno'd and tested. 1600CC CLASS 5 OR ½ 1600 Built By Art Thraen 2009 78HP and 102LB TQ 12.1:1 Compression $6500.00 ACE 360 w. 6100 so. #A SLC, UT. 84107 801-943-1234 1. NEW OEM mag case, shuffle pinned, 911 oilers to pistons, full flowed, and race prepped @ ACE. 2. DPR 85.5mm Race prepped crank, Flywheel 12lb, Balanced Rods, balanced 2100lb pressure plate (kit) 1599cc 3. CAM: Special Offroad grind by ACE, for the 1600 engine, dual pattern lift/dur. 4. Oil Pump: ACE prepped 26mm, full flow plugged 5. Head Studs: Chromolly 6. Piston/Cyls: Mahle Forged 85.5, Balanced

These are set up, at ACE, Tested prior to sale.. Have many ACE tricks and run great! Call fo pricing, Most of the time I have on on the shelf..

1600cc SINGLE PORT.. Runs great and was cleaned up and tuned by Art @ ACE.. FOR SALE $1199.00 This engine is complete!!!!!

Spark Plug Install tool, works with 12mm and 14mm plugs.. Keeps from cross threading.. $6.99ea

IDA Air Filter Rings, Made of 308 Stainless Steel.. Used to compensate for the thickness of the air filter on IDAs.. makes the Volocity stack push down on the Sec. Venturi.. A most for 48 IDA's with air filters

Choke Block Off Plates, fro IDF and Zeniths.. .120" stainless... Use the old screws.. $7.95ea

Porting Patterns, 1/4" steel, These are used to port your own heads, two popular Port designs. $12.95ea

Rebuilt engine Cases, At ACE we rebuild our Cases, You can send in your case and have it rebuilt and alignBored/Decked/cut for Larger Cyl/Cam reamed here at ACE. We do the machine work and the cleaning.. Call for pricing

This is the best tool Iv found for installing sealents, I sell them for $15.99 Money back guarantee! Try One!

"Copperhead Cluch Disc" |The best clutch disc on the market for the high-performance VW ...Made in the USA. 200 mm in size weighs 840grams/1.13 lb..Used in or race car for years without failure and over 200 sold to date without problems. The backing plate is copper to absorb heat and the soft lining is an asbestostype lining that will recover from abuse. very smooth engagement. will last for years! (do not use on cast iron cheapo flywheels) made for original german flywheels and chrome-moly flywheels Cost $99.95 "Copperhead Cluch Disc" |The best clutch disc on the market for the high-performance VW ...Made in the USA. 200 mm in size weighs 840grams/1.13 lb..Used in or race car for years without failure and over 200 sold to date without problems. The backing plate is copper to absorb heat and the soft lining is an asbestostype lining that will recover from abuse. very smooth engagement. will last for years! (do not use on cast iron cheapo flywheels) made for original german flywheels and chrome-moly flywheels Cost $94.00

Bushings @Transmission Intermediate housing, We do this machining proceedure here @ ACE if the factory holes are loose.. $35.00

Jet Nuts for exhaust and intakes, 3/8 wrench X 8x1.25 Thread, call for prices

ACE carb arms for DRLA/IDF thicker then the weber or CB arms and made of #308 stainless, $7.95 ea.

48 IDA Volocity stack clips made from #308 stainless, thicker the the OEM Clips, and are less prone to bending. $20.00 for a set of 8

Return spring Kit for the IDA, layed out on a table. $24.95

48 IDA Return Spring Kit, Built by ACE, Works with CB Linkage and EMPI, Bugpack, Etc. $24.95

Rebuilt type 1 and type 2 transmissions, starting at $520.00

New Engines, 1600cc to 2387cc, we build them from scratch and do 90% of the machine work here at ACE. we have dyno services, and can tune your new engine to profection! Call for prices

Tie Downs for VW RaceCar, sand Rail. Comes with Metric bolts and nuts and washers, Cad plated, Laser cut. $24.99 set

OEM VW trans mounts, I have the nose mounts too, Pad mounts in stock, I buy 100 at a time, I will have them in stock, Call for

oil by pass system, call for prices

MOCAL, by pass thermostat plate, allows oil to warm up, @ 160 degrees allows oil to oil cooler, used on all our own Cars! $135.00